工程铜门由于其良好的外观和耐用的特性受到不少家庭的喜爱，那么，你知道工程铜门应该怎样安装吗？先是确定工程铜门的尺寸了，其次安装工程铜门前要提前在墙上打好门洞。然后准备好各种工具材料就可以进行安装了。接下来就和山东铜门厂家一起看下工程铜门的三种安装方法吧。

Engineering copper doors are loved by many families due to their good appearance and durability. Do you know how to install engineering copper doors? Firstly, the size of the engineering copper door has been determined. Secondly, before installing the engineering copper door, it is necessary to make the door hole on the wall in advance. Then prepare various tools and materials for installation. Next, let's take a look at the three installation methods for engineering copper doors with Shandong copper door manufacturers.

一、工程铜门一般的安装方法

1、 General installation methods for engineering copper doors

1、测量洞口规格是否相等。如小于工程铜门的规格，应铲除友皮。

1. Measure whether the specifications of the openings are equal. If it is smaller than the specification of the engineering copper door, the skin should be removed.

2、工程铜门按洞口位置摆平放平，在门框的四个安装孔用M12钻头钻孔，用M12母栓固定后再进行调整。

2. The engineering copper door should be leveled according to the position of the opening, and the four installation holes of the door frame should be drilled with M12 drill bits, fixed with M12 bolts, and then adjusted.

3、调整方法：以门扇外面为基准平面，检验门框安装后是否与门扇平行。如果门框与门扇不平行，在门框背面靠近螺丝位置加木垫试垫，直到门扇平行为止。

3. Adjustment method: Using the outside of the door leaf as the reference plane, check whether the door frame is parallel to the door leaf after installation. If the door frame is not parallel to the door leaf, add a wooden pad on the back of the door frame near the screw position until the door leaf is parallel.

二、填充水泥法安装工程铜门

2、 Filling cement method for installation of copper doors in engineering

1、因为工程铜门门框是空心的，为了使工程铜门更加牢固，必须在门框空心处填充水泥，在填充水泥前把门关好，请注意在门扇开启面，门框与门扇之间应加塞纸垫。

1. Because the door frame of the engineering copper door is hollow, in order to make the engineering copper door more secure, it is necessary to fill the hollow part of the door frame with cement. Before filling the cement, close the door properly. Please note that paper pads should be added between the door frame and the door leaf on the opening surface of the door leaf.

2、填充水泥不能过量，否则使门框变形，影响门的使用和开启。

2. Do not overfill with cement, otherwise it will deform the door frame and affect the use and opening of the door.

3、填充水泥24小时后将纸垫取下，轻轻打开门扇，用螺丝刀将框内钻孔部位的水泥刮干净，再把安装孔盖住。

3. After 24 hours of filling with cement, remove the paper pad, gently open the door leaf, use a screwdriver to scrape the cement from the drilled area inside the frame, and then cover the installation hole.

4、如果框内不填充水泥，影响使用功能，后果自负。

4. If the box is not filled with cement, it will affect its functionality and the consequences will be borne by oneself.

三、使用安装片安装工程铜门

3、 Install engineering copper doors using installation plates

1、把门扇取下，将门框放进门洞，用水平尺铅垂检查是否摆放平整。若不平整，用木片垫平整。

1. Remove the door leaf, place the door frame into the door opening, and use a level ruler to plumb it to check if it is placed smoothly. If it is not flat, use a wooden pad to level it.

2、先以内门校一侧作基准边，把门框加强筋上的安装片旋转与门框垂直，然后将安装片折弯，用水泥钉固定于墙上。

2. First, use one side of the inner door as the reference edge, rotate the mounting plate on the door frame reinforcement to be perpendicular to the door frame, then bend the mounting plate and fix it to the wall with cement nails.

3、将内门套上门框并锁好，在确保平整的情况下，相继把内门锁侧安装片固定在墙上。

3. Cover the inner door with the frame and lock it, while ensuring flatness, successively fix the side mounting plates of the inner door lock to the wall.

4、用同样的方法将外门套上门框，固定好安装片。

4. Use the same method to cover the outer door frame and fix the installation plate.

5、检查内门、外门开关是否灵活，若有异常，可塞木片做进一步调整。

5. Check whether the inner and outer door switches are flexible. If there are any abnormalities, wooden blocks can be inserted for further adjustment.

6、在门框与墙之间缝隙处均塞木片，使门框校为稳定，然后往门框内灌注水泥沙浆，将水泥沙浆凝固干燥后把门缝外木片取出方可使用门的功能，但在24小时内尽量是少开启次数和力度。

6. Insert wooden pieces at the gaps between the door frame and the wall to make the door frame stable. Then pour cement mortar into the door frame, solidify and dry the cement mortar, and remove the wooden pieces outside the door joint before using the door function. However, try to open the door less frequently and with less force within 24 hours.

工程铜门的三种安装方法具体内容就讲解到这里了，希望能够给您好的帮助，更多事项就来我们网站http://www.jnqianfu.com留言咨询吧！

That's all for the specific content of the three installation methods for engineering copper doors. We hope to provide you with good help. For more information, please come to our website http://www.jnqianfu.com Leave a message for consultation!